Honeywell Hot Water Heater No Status Light: 5 Possible Reasons And Solutions

Is your Honeywell hot water heater no status light? Looking for the best solutions? Don’t worry! You’ve found the right place for the proper solution.

The Honeywell status light can go off for various reasons, like a dirt accumulation or misalignment. In some cases, these are solvable, but sometimes replacement is a better solution.

First, identify the appropriate problem, then make the right decision. Our team is ready to top 5 common reasons to make it easier.

In this context, we will discuss the reasons with solutions. You will get the best result hopefully from us. Let’s see which one is the reason for your concern.

Why Honeywell Hot Water Heater No Status Light: Better Suggestions

There are many reasons why the Honeywell hot water heater thermostat has no status light. Find out the most common causes in the table given here.

Possible Reasons	Solutions
Dirty base ring & pilot	Clean and remove the flammable substance.
Igniter faulty	Check out the wire & voltage.
Tangle in the flex tube	Uncurl from the tube.
Defective thermocouple	Should replace in case of excess.
Control board fail	Replace a control board

The above discussion could explain the exact reason for no status light. Try to solve from the fixing steps which are related to your function.

Dirty Base Ring And Pilot

The Honeywell hot water heater control no status light, so be alert. The pilot tube & base ring is part to help with the status light.

But sometimes, it collects dust and junk by airflow. In that case, you got a heavy coating of junk that lost its function.

Follow the instructions.

• Now we will solve the problem given here
• First of all, separate the electric connection
• Now gently enter a needle on the pilot
• Smoothly clean it with emery cloth
• Ensure the pilot is dust-free
• Check it out and wait for the lights to turn on

Hopefully, you can go to the goal. If it does not work, check the next…

Solve The Igniter Faulty

The igniter is working on the burner light functioning. Some controls are using the lighter for fuel consumption. After 90 seconds, it does not run on the light.

So do something to resolve it.

• First, check all wire connections.
• See if the white or orange wire is firmly attached to the system
• Set it in such a way so that the metal does not touch
• Tighten the screws well
• Pop the igniter a few times
• Then check the voltage option whether there is light
• If work then good

But if not, get an idea from the next reason and fix the idea.

Tangle In The Flex Tube

The tube is used to fuel burn in the Honeywell water heater gas controller. But sometimes, the system may be a kink in this. It can put the procedure in trouble.

If you think it’s solvable, then do the rest of them tangle-free slowly. Moreover, you can be a little careful.

• Unplug all connections
• Remove all flammable substances like gasoline, thinner, and others.
• It may produce bad vapors, which can cause a risk of death.

Otherwise, the best solution would be to change it. Check out the next.

Defective Thermocouple

Pilot penstock is a good combination of thermocouples activities. The thermostat mentions the pilot’s tube running capability. It is designed to be isolated by its electric gesture.

Whenever a diode may face any issues, it keeps the gas supply offline. This problem can be realized when the pilot is out of the heat water tank. Look at the activities to solve it.

• Get rid of overheating during the device.
• Make sure the control has cooled.
• Then collect a piece of good sandpaper
• Gently wipe the top with the thermocouple.
• Do it in such a way that if there is any sand, it will come out.
• Now reinsert to see if the lights are on.
• After a while, the light came on
• You are lucky, guys!
• Might not, Test the activities with a meter.
• If its reading is not above the 20MV, then there will be nothing to do
• It needs to be replaced for protection and better service.

If you look at the thermocouple bent far away from the pilot, you must understand that it is damaged or crippled.

Control Board Fails

When Honeywell hot water heater has no status light, check the Control board, there is a central activity in the whole process. It involves every option internally.

Not working in any step & bad reading position in multimeter of course, will be one of the reasons why the status light is not coming.

The control board has failed. Replace a new one on your device. Call a technician if you are inexperienced.

This Video Will Help You Too!

Frequently Asked Questions (FAQs)

Final Wrap

We have created an ultimate guide after in-depth research. It has already shown the Honeywell hot water heater no status light reasons and solutions. As a reader, you also learned the matter from this article.

Now start working on a problem that matches your device. Hopefully, you can do it without any technician. In some cases, do special instruments have to be checked?

So it can be difficult and expensive. If you are inexperienced, then seek the help of an expert. Have any questions. Would you mind sharing to feel free? We’ll try to stay there. Stay warm. Stay with us.

You Can Also Read:

• P Trap Lower Than Drain Pipe- Why & Is It Legit?
• How To Add A Tee To Copper Pipe- Easy Steps
• How to Use Drummond Water Pump| 3 Must-Know Points!
• [Experts Answer] Where To Install Check Valve On Water Pump?

Check out our Reusable Bamboora Paper Cloth Towels

While shaping the aim of making the environment clean and healthy, Bamboora deals with the production of natures way bamboo paper cloth towels. These bamboo towels are better for the environment. Along with doing lots of plumbing work, they are usable for other house chores too. From wiping out the spill on the floor to cleaning the dust, bamboo paper towels effectively perform their work. They are effective in replacing regular cloth towels that you often purchase. The natural strength and softest fiber of bamboo make them one of the best sustainable bamboo paper towels.