How to Raise Bathroom Sink Plumbing- Easy Ways

If you are thinking of raising sink drain pipes to a new height or fitting them into a new vanity plumbing area, there are several ways to do this task. But how to raise bathroom sink plumbing? You can rotate the P-trap and try to increase the height, or there are some alternatives mentioned below.

So, arranging the bathroom vanity to the perfect appearance needs to set the sink plumbing area first. Most of the time, the height of vanity might seem too short. So, to fix this problem, you must know how to raise the pipe settings over a few inches.

In this article, we will show you a few techniques to change the look of your bathroom sink plumbing area to your desired look.

How to Raise Bathroom Sink Plumbing

While theBathroom sink drain outlet is too low, it is pretty disturbing every time, no matter what we are up to. In this part, we have sorted out three ways that you can raise the bathroom sink plumbing area. Have a look and try the one that fits your desired height.

  • By rotating the P-trap slightly to a certain angle
  • Rotating the P-trap and adding a small pipe
  • Adding a longer pipe length with the existing arrangement
READ ALSO  How To Raise Toilet Flange 2 Inches With 5-Easy Steps

Don’t start yet! We have a lot to explain. So, read each method carefully; otherwise, you might mess it up, and who knows, it will cost you way more than you tried to save.

Oh, if you need, have a look at the standard sizing for laundry sink stub out height.

To Move The Sink Over Two Inches

In this method, you will not require to add any extra fittings to raise the height. The only tool you will require is a pipe wrench. Then follow the steps below,

  1. pull out the linking pipe of the mainline.
  2. Then turn the P-trap into an angle.
  3. Add a small piece of pipe right at the joining point of the mainline linkage and the P-trap.
  4. Connect them using the pipe wrench.

Notes: The only issue you need to keep in mind is that the mainline link may leak while pulling out. So, it is recommended to prepare a new one before disassembling the fittings.

To Move Six Inches Away

this method is to raise bathroom sink drain height up to at least six inches. We will need to add a 22.5-degree fitting, a small section of pipe, and a connector fitting. Then do as follows,

  1. Pull the linking pipe out further than before.
  2. Take the P-trap to your ease.
  3. Add a 22.5 degree fitting upward.
  4. Add a small pipe piece in between the P-trap and the 22.5-degree fitting.
  5. Joint all the parts using a pipe wrench.

Notes: If the piping system is cast iron made, the joint parts might be rusted. So, while pulling out the linking pipe, the threads could damage, or leakage might occur.

To Move Eight to Ten Inches

How do you raise a low bathroom sink at least up to eight inches? Well, now you will need a longer pipe piece with the other fittings. The first two steps will be the same as the previous method. Then just follow these steps,

  1. Add a 45-degree fitting upward.
  2. Add a comparatively larger pipe piece (depending on the height you require) between the P-trap and the 45-degree fitting.
  3. Joint all the parts using a pipe wrench.
READ ALSO  Caroma Vs Toto- Which Should Be More Your Preference?

Notes: In the case of the cast iron piping system, be aware of damage as the previous method.

You May Like This Video Too!

Frequently Asked Questions (FAQs)

Can you raise a bathroom sink?

Of course. It just needs a few fittings adjustments from the mainline to the sink. The sink connector pile branching from the main plumbing area is already adjusted outside of the wall using some fittings. So, you need to disassemble the pipe from the mainline and use a new fitting according to the height we are willing to raise the sink too.

What if the new sink drain doesn’t line up with the existing pipes?

When the new sink drain doesn’t line up with existing pipes, try moving the trap to its original position. A flexible tailpiece extension might help you out in this situation. Take a pipe wrench and tighten up the P-trap locking collar over the tailpiece. Avoid over-tightening.

Why are bathroom vanities so short?

The standard height of the bathroom vanities is typically around 32’’ to 36’’. This height is short considering the average human height because of the ease of children’s reach. Although when the height is 36’’, it might require to use of a step tool for a kid.

Final Words

So, did you figure out how to raise bathroom sink plumbing? We think you did, and if not, it is better to call for a professional plumber. If you have skipped any of the parts, then let m=us inform you that we have linked up the topics in some cases, so don’t get started right away because you might have missed the vital steps and warnings of these three methods.

READ ALSO  You Asked for American Standard Bathroom Faucet Parts Diagram! (Here It Is)

Take your time and have a thorough read of the article. It is better to get a primary idea of the arrangements of the parts under the sink to avoid unnecessary hassle.

You Can Also Read:

Check out our Reusable Bamboora Paper Cloth Towels

While shaping the aim of making the environment clean and healthy, Bamboora deals with the production of natures way bamboo paper cloth towels. These bamboo towels are better for the environment.
Along with doing lots of plumbing work, they are usable for other house chores too. From wiping out the spill on the floor to cleaning the dust, bamboo paper towels effectively perform their work. They are effective in replacing regular cloth towels that you often purchase. The natural strength and softest fiber of bamboo make them one of the best sustainable bamboo paper towels.

Similar Posts